Features: 1Multi Function: This optical fingerprint module can complete fingerprint collection, fingerprint registration, fingerprint comparison and fingerprint search function independently. 2Self Learning: In the process of fingerprint recognition, the latest fingerprint characteristic values will be integrated into the fingerprint database. 3Autocorrection: This fingerprint reader module supports 360 degrees autocorrection and auto identification, which allow you to press the correctly registered finger at any angle. 4Low FAR: This fingerprint reader sensor features maximum 0.0001% low false accept rate, that is, when randomly pick one fingerprint in 1 million fingerprints to compare with the others, only one fingerprint in 1 million will be successfully identified and passsed. 5Low FRR: This optical fingerprint reader adopts 0.0001% low false rejection rate. Among the existing 1 million fingerprints, if 1 million fingerprints are compared 1 million times in any order, only one identification fails. Item Type: Optical Fingerprint Module Material: ABS CPU: 120MHz Main Frequency, 1M Bits Flash Memory, 128KB SRAM Fingerprint Collector: CMOS Image Sensor, Optical Total Reflection Principle Fingerprint Registration Capacity: 1000 by Default and 3000 Can be Expandable False Recognition Rate (FAR): < 0.001 % (Security Level: 3) False Rejection Rate (FRR): < 0.1% (Security Level: 3) Comparison Method: (1: N) and (1:1) Comparison Fingerprint Template Size: 570 Bytes Security Level Setting: Level 1 to Level 5. Factory Setting: Level 3 Fingerprint Feature Extraction Time: < 0.45 Seconds (1: N) Comparison Time (When 3000 Fingerprints Are Fully Registered): < 1.5 Seconds Communication Interface: UART,3.3V TTL Level Serial Communication Parameters: No Parity= None, One Stop Bit = 1 Flow Control None = None Baud Rate: 9600, 19200, 38400, 57600, 115200 (bps) Factory Setting: 115200bps Operating Voltage: Win Voltage (DC3.3V10%) Working Current: Less Than 100mA Interface Definition RST: Reset the Module, and the Low Level is Valid (this Pin is Needed in the Case of Uninterrupted Power Supply to the Module, and It is Recommended to Be Suspended in Other Cases) VIN: Main Power Supply for the Fingerprint Module, 3.3V by Default GND: Power Ground RX/DP: Module Receives Data Pins TX/DN: Module Sends Data Pins 3.3V: Finger Detection Function Circuit Power Supply Wakeup: Output Pin of Finger Detection Function, Output High Level when Finger Presses On Note: 1. in Addition to the Fp Cancel Instruction in the Communication Process, the Sending and Receiving of Other Instructions Must Follow the Principle of One Sending and One Reception, and the Interval Between the Two Instructions is Required to Be Greater Than or Equal to 20ms, Less Than This Time May Cause the Subsequent Instructions Not to Respond. 2. when Transmitting More Than 24byte Data from the Module Target to the Host, Use the Response Data Packet. 3. when Host Does Not Receive a Reply, Please Do Not Send Instructions to Target. 4. the Module Indicator Light Does Not Need to Be Controlled by Default, and the Collector Indicator Will Be Automatically Turned on when Processing Instructions, and if the Correct Fingerprint is Collected, the Indicator Will Be Automatically Turned Off if the Correct Fingerprint is Not Collected, the Collector Light is Always On. when Using, You Can Also Use the Sensor Led Control Command to Control the Turn on or off the Collector Indicator According to Your Needs. 5. This Device Has a Password Protection Mode, After the Device Password is Set, Most of the Instructions Cannot Be Used Without Password Confirmation. if You Do Not Set a Device Password, You Can Use All Commands Without Password Confirmation. 6. the Module Will Automatically Enter the Initialization when It is Powered On, the Time Needs About 300ms, It is Recommended to Send Instructions to the Module After Waiting for 350ms After Powering on the Module. 7. This Module Has Automatic Finger Detection Function, That Is, in Low Power Mode, There is a Finger Pressed on the Fingerprint Collector, and the Wakeup Pin of the Module Will Output a High Level. the Specific Operation is As Follows: (1). the 3.3v of the Module Should Be Kept in Power and Cannot Be Disconnected. (2). when Low Power Consumption is Needed, Disconnect the Vin Power Supply. when a Finger Touches the Glass of the Fingerprint Collector, the Wkp Pin of the Module Will Output High Level, and then Change Back to Low Level After Finger is Away. (3). After Detecting the High Output Level of Wkp, when the Fingerprint Module Needs to Work, Switch on the Vin Power Supply, and Send Instructions to the Module After 350ms. Package Included: 1 x Optical Fingerprint Module