Item Type: ECU Decoder <br>Material: ABS <br>Size: Approx. 66 x 43mm/2.6 x 1.7in <br>Wiring: <br>+: 12v DC <br>-: GND <br>S: Signal wire <br>Instructions for Use: <br>After powering the device on - the LED should flash twice. The sweeping process starts as power is supplied to the device. LED ON - means there are pulses on the output. <br>After reaching the lowest frequency the LED goes off and the mcu stops the generation. <br>* Connect the GND line to any suitable GND on the ECU via the small grabber. <br>* Connect the Data line to the Reset pin on the EPROM via the small grabber. <br>* Power the ECU and then the sweeper, the sweeper will flash twice on power up. <br>* Press the button and the device will start sweeping, once the LED turns off your done. <br>* Cut the immo data line on the ECU before re-fitting back to car. <br> <br> <br>TMS-374 Decoder ECU info <br>The sweeper should work with the following ECUs: <br>Fit for Renault SIEMENS Fenix 3 and 5 <br>Fit for Renault Megane 1400cc 8v <br>Fit for Renault Megane 1600cc 8v <br>Fit for Renault Megane 2000cc 8v <br>Fit for Renault Megane 2000cc 16V <br>Fit for Renault Megane Scenic 1400cc 8v <br>Fit for Renault Megane Scenic 1600cc 8v <br>Fit for Renault Megane Scenic 2000cc 8v <br>Fit for Renault Sefrane 2000cc 16V <br>Fit for Renault Laguna 2000cc 8v <br>Fit for Renault Laguna 2000cc 16v <br>Fit for Renault Espace 2000cc 8v <br>Fit for Renault SAGEM SAFIR 1 and 2 <br>Fit for Renault Clio 1200cc 8V <br>Fit for Renault Clio 1400cc 8V <br>Fit for Renault Clio 1600cc 8V <br>Fit for Renault Clio 2000cc 16V Williams <br>Fit for Renault Laguna 1800cc 8V <br>Fit for Renault Laguna 2000cc 8V <br>Fit for Renault Laguna 1800cc 16V <br>Fit for Renault Laguna 2000cc 16V <br>Fit for Renault Twingo 1200cc 8V <br> <br>NOTE: If reset pin is connected to ground then it must be lifted or the track cut before decoding. This can be re-attached after decoding the ecu. <br>As a rule of thumb keep the power connected to the ECU for a futher five minutes after the decoder has completed the decoding process. <br> <br>for Sagem SL96 Psa <br>Fit for Peugeot 306 1400cc 8V <br>Fit for Peugeot 306 1600cc 16V <br>Fit for Peugeot 306 1800 16V <br>Fit for Peugeot Ranch 1400 8V <br>Fit for Citroen Berlingo 1400cc 8V <br>Fit for Citroen Xrara 1400cc 8V <br>Fit for Citroen Xrara 1800cc 16V <br>Fit for DAEWOO SIEMENS <br>Fit for Daewoo Matiz 800cc <br>Fit for HYUNDAI SIEMENS <br>Fit for Hyundai Coupe 1600cc 16V <br>Fit for Hyundai Coupe 2000cc 16V <br>Fit for KIA SIEMENS <br>Fit for Kia Rio 1300 16V <br>Fit for Kia Rio 1500 16V <br>Fit for MAGNETI MARELLI <br>1AP20, 1AP40, 1AP41, 1AP43, 1AP80, 1AP81, 1AP83 1AP90, <br>Fit for Citroen Berlingo 1800cc 8V <br>Fit for Citroen Saxo 1400cc 8V <br>Fit for Citroen Saxo 1600cc 16V <br>Fit for Citroen Xara 1400cc 8V <br>Fit for Citroen Xara 1800cc 8V <br>Fit for Citroen Xara 2000cc 16V <br>Fit for Citroen ZX 1400cc 8V <br>Fit for Peugeot 106 1400cc 8V <br>Fit for Peugeot 106 1600cc 8V <br>Fit for Peugeot 106 1600cc 16V <br>Fit for Peugeot 206 1100cc 8V <br>Fit for Peugeot 206 1400cc 8V <br>Fit for Peugeot 306 1400cc 8V <br>Fit for Peugeot 306 1600cc 8V <br>Fit for Peugeot 306 1800cc 8V <br>Fit for Peugeot 405 1800cc<br>1、Frequency sweeper with 5V square wave output (duty cycle is 50%, effective frequency range from 10kHz above (maximum 50kHz) to 50Hz). <br>2、It can be regarded as the MCU version of the software TMS?374 decoder ECU. The only difference between the two tools is that the MCU version does not require a PC to work. <br>3、Use a small MCU instead of the PC RS232 Tx line to generate pulses, which has stable and professional performance. <br>4、The effective range is from about 2000Hz to about 100 Hz. The functions of the sweeper are exactly the same, but the effect is better (larger range). <br>5、Decode ECU into a new state without the need for PC. There are wiring instructions to reduce your error rate, simple operation.1 x ECU Decoder